@journ start here bud.
Alien Power System 2.4Ghz Remote control
Is it worthwhile adding a post for commonly used carbon fiber/ vacuum bagging suppliers? Am having trouble locating breather ply here in Australia. edit - just found one in china that ships at a decent price here
What motor are you using? I was planning on using the NTM Prop Drive 50-60 270KV / 2400W but am worried that I wonāt get any speed using a 6s8p setup (18650 25R from Samsung -2400mah capacity constant, 20A current). What torque ratios and wheels are recommended (I am only 105 pounds) and want to make my first board in September on a Ā£300 budget.
controller: AlienPowerSystem (UK) for those in europe.
Wheels (Recommended to get plastic spoked wheels above 80mm)
MBS All Terrain Longboard Wheels 100m
I think this would work nicely for balance wires
1 Like
I have 15mm 15t steel motor pulleys and 40t aluminum pulleys that are designed for abec flywheels and MBS all terrain wheels
Anyone used this monster?
You got some nice builds man! I saw these motors on aliexpress a few months ago, I think they are the same as yours. Whatās your opinion about your motorās? https://nl.aliexpress.com/item/New-Arrival-Brushless-Outrunner-Motor-N5065-270KV-1665W-For-DIY-Electric-Skate-Board/32793724521.html?spm=2114.13010308.0.0.JIWXfw
1 Like
@bartroosen12 I used those motors in my wife and kids board. They work very well. Itās been about 9 months since they first road on the board with them installed. They ride there boards almost every day with no problems. Incline and torque is on the low end. Itās best to push start before forward throttle. Once going itās a wonderful ride and pretty fast. Especially for my wife and kids.I like these motors for them. Once I feel more comfortable with there skills. Iāll move them up to something more powerful.
1 Like
Might consider adding DIYās 6355 190kv motor 
Iām gonna be using that and Iāve seen it all over the place
Hi every, theri is something I canāt understand: How can the max current be 65 A for 190KV Electric Skateboard Motor 6372 and for Maytech 6355 230 KV Moteur, whereas they can each develop more than 3500 W with 12 S ?
Thx in advance
Enertionās Nano X controller
How do you feel about the amount of thumb push and pull? Do you find it sufficient? I would think the Raptor 2 guys would praise having the slow mode considering how quickly and abruptly this controller can launch my 10s spud on hummies
Hoya, I know itās been a while since the post but what settings did you use with the yep 80 esc
I dont know anymoreā¦ But i can say that you should rather buy a vesc derivative instead of changing the settings 
Thanks for getting back to me, Iāve got two hanging around looking for something to do, they where for an old project. Iām trying to get some vescs in the UK but itās hard 
Thanks anyway!!!
Single, Dual VESC 4.12 Cases
https://shop.3dservisas.eu/collections/cases/products/aluminium-case-for-vesc-v4-12-bldc-motor-controller https://shop.3dservisas.eu/collections/cases/products/aluminium-case-ver-2-for-dual-vesc-v4-12-bldc-motor-controller
Single, Dual with/without Fins FocBox Cases:
https://shop.3dservisas.eu/collections/cases/products/dual-focbox-case-with-cooling-fins-v2 https://shop.3dservisas.eu/collections/cases/products/dual-focbox-case-without-cooling-fins https://shop.3dservisas.eu/collections/cases/products/single-focbox-case-without-cooling-fins
Trampa/TB218 Geared DriveTrains
Wheel Hub for Pneumatic wheels
18650 cell building PCB
1 Like
Sorry for the dumb question. But I didnāt find it as obvious as you might think it is. But who is the guy referred to as DIY? If you Google that you get a lot of sites with diy in the address. Please post the exact website?
Plus. Anyone have experience with the Hobbyking VESCs? The HK buyers rate them high enough